'55 Chevy 3800 Cummins

6DoF · 02-15-2021, 10:45 PM

so i did return the 30" natural finish steering column and got a 28" all black. the 3 different materials/textures of the natural was pissing me off, and the less 2" should put me only JUST thru the firewall for better steering shaft angles.

so funny story, i returned it directly to the Summit Racing warehouse where i like to go thru the scratch n dent pile. well they got rid of it, and that sux, hopefully coming back after renovations cuz even the staff was pissed. so i'm getting my gift card credit at the cashier and with no one else in line i ask for some extra help. their online order history is only 3 years and i've already lost access to orders i made for this truck. i asked if she could print out my entire order history for me to scan back into a PDF. sure thing! so she proceeds to then tell my wife how much i've spent at summit racing since 2013.

so i set about getting the 12V placement figured, that was a b!tch. at one point i got it stuck between the chassis and cab and had to just start cutting, but at least it was stuff i needed to eventually cut anyways. it "fits". engine/trans and chassis are sitting on separate jack stands ready for mounts. i have them all drawn up, but need to get the plate cut now ... i really need my own plasma table ...

firewall reference for how far back it is, the #6 cylinder is totally behind it. the '55 AL radiator is in basically the stock placement to check clearance, and there is some. fun fact: there is 11" from the rocker of a 1955 chevy truck up to the under side of the floor. and yet, with an nv5600 sitting on the ground it still requires cutting! that trans is literally in there with the bottom parallel to the ground and the same 0.5" above the bottom of the frame that the rockers are.

please excuse the second "rock out selfie" ... it just keeps happening!

:metal:

02-15-2021, 10:45 PM	#11
6DoF AKA: jeepnski Join Date: Sep 2002 Location: Pittsburgh, PA Posts: 16,886	so i did return the 30" natural finish steering column and got a 28" all black. the 3 different materials/textures of the natural was pissing me off, and the less 2" should put me only JUST thru the firewall for better steering shaft angles. so funny story, i returned it directly to the Summit Racing warehouse where i like to go thru the scratch n dent pile. well they got rid of it, and that sux, hopefully coming back after renovations cuz even the staff was pissed. so i'm getting my gift card credit at the cashier and with no one else in line i ask for some extra help. their online order history is only 3 years and i've already lost access to orders i made for this truck. i asked if she could print out my entire order history for me to scan back into a PDF. sure thing! so she proceeds to then tell my wife how much i've spent at summit racing since 2013. so i set about getting the 12V placement figured, that was a b!tch. at one point i got it stuck between the chassis and cab and had to just start cutting, but at least it was stuff i needed to eventually cut anyways. it "fits". engine/trans and chassis are sitting on separate jack stands ready for mounts. i have them all drawn up, but need to get the plate cut now ... i really need my own plasma table ... firewall reference for how far back it is, the #6 cylinder is totally behind it. the '55 AL radiator is in basically the stock placement to check clearance, and there is some. fun fact: there is 11" from the rocker of a 1955 chevy truck up to the under side of the floor. and yet, with an nv5600 sitting on the ground it still requires cutting! that trans is literally in there with the bottom parallel to the ground and the same 0.5" above the bottom of the frame that the rockers are. please excuse the second "rock out selfie" ... it just keeps happening! :metal: Last edited by 6DoF; 02-16-2021 at 06:54 AM.